SY10E171JZ TR

■ ■ ■ ■ ■ 725ps max. D to output Extended 100E VEE range of –4.2V to –5.5V Differential outputs Split select architecture Fully compatible with industry standard 10KH, 100K ECL levels ■ Internal 75KΩ input pulldown resistors ■ Fully compatible with Motorola MC10E/100E171 ■ Available in 28-pin PLCC package The SY10/100E171 offer three 4:1 multiplexers with differential outputs, designed for use in new, highperformance ECL systems. The leading 4-bit multiplexer operation is organized pairwise, with each pair being a 2bit multiplexer. Separate select (SEL1A, SEL1B) controls are provided within each pair. The SEL1A and SEL1B signals control the leading multiplexers, while the SEL2 signal controls the output multiplexer. The three select signals can be used to determine which of the four data inputs will be propagated to the corresponding outputs. PIN NAMES BLOCK DIAGRAM Pin D0b D0c D0d D1a D1b D1c D1d D2a D2b D2c D2d SY100E171 DESCRIPTION FEATURES D0a SY10E171 SY100E171 SY10E171 3-BIT 4:1 MULTIPLEXER Micrel, Inc. 2:1 MUX SEL 2:1 MUX SEL 2:1 MUX SEL 2:1 MUX SEL 2:1 MUX SEL 2:1 MUX SEL 2:1 MUX SEL Q0 Q0 2:1 MUX SEL Q1 2:1 MUX SEL Q2 Function D0x–D2x Data Inputs SEL1A, SEL1B First-stage Select Inputs SEL2 Second-stage Select Input Q0–Q2 True Output Q0–Q2 Inverted Output VCCO VCC to Output Q1 Q2 SEL1A SEL1B SEL2 M9999-032006 hbwhelp@micrel.com or (408) 955-1690 Rev.: E 1 Amendment: /0 Issue Date: March 2006 SY10E171 SY100E171 Micrel, Inc. Ordering Information(1) VCCO D2b D2a D2d D2c D1b D1a PACKAGE/ORDERING INFORMATION 25 24 23 22 21 20 19 SEL1A SEL1B 26 18 27 17 SEL2 VEE 28 16 NC TOP VIEW PLCC J28-1 1 2 15 VCC Q1 14 Q1 VCCO Q0 13 4 12 9 10 11 Q0 8 VCCO 7 D0c D0d 6 D0b 3 D1d D0a NC D1c 5 Q2 Q2 Part Number Package Type Operating Range Package Marking Lead Finish SY10E171JC J28-1 Commercial SY10E171JC Sn-Pb SY10E171JCTR(2) J28-1 Commercial SY10E171JC Sn-Pb SY100E171JC J28-1 Commercial SY100E171JC Sn-Pb SY100E171JCTR(2) J28-1 Commercial SY100E171JC Sn-Pb SY10E171JZ(3) J28-1 Commercial SY10E171JZ with Pb-Free bar-line indicator Matte-Sn SY10E171JZTR(2, 3) J28-1 Commercial SY10E171JZ with Pb-Free bar-line indicator Matte-Sn SY100E171JZ(3) J28-1 Commercial SY100E171JZ with Pb-Free bar-line indicator Matte-Sn SY100E171JZTR(2, 3) J28-1 Commercial SY100E171JZ with Pb-Free bar-line indicator Matte-Sn 28-Pin PLCC (J28-1) Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals only. 2. Tape and Reel. 3. Pb-Free package is recommended for new designs. M9999-032006 hbwhelp@micrel.com or (408) 955-1690 2 SY10E171 SY100E171 Micrel, Inc. TRUTH TABLE Pin State Operation SEL2 H Output c/d data SEL1A H Input d data SEL1B H Input b data DC ELECTRICAL CHARACTERISTICS VEE = VEE (Min.) to VEE (Max.); VCC = VCCO = GND TA = 0°C Symbol Parameter TA = +25°C Min. Typ. Max. Min. Typ. IIH Input HIGH Current IEE Power Supply Current 10E 100E TA = +85°C Max. Min. Typ. Max. Unit Condition µA — mA — Unit Condition ps — ps 1 ps — — — 150 — — 150 — — 150 — — 56 56 67 67 — — 56 56 67 67 — — 56 65 67 77 AC ELECTRICAL CHARACTERISTICS VEE = VEE (Min.) to VEE (Max.); VCC = VCCO = GND TA = 0°C Symbol tPD tskew tr tf Parameter Propagation Delay to Output D SEL1 SEL2 Within-Device Skew Dnm, Dnm to Qn Da, Db, Dc, Dd to Q Rise/Fall Time 20% to 80% TA = +25°C TA = +85°C Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. 275 450 350 480 650 550 650 850 700 275 450 350 480 650 550 650 850 700 275 450 350 480 650 550 650 850 700 — — 60 40 — — — — 60 40 — — — — 60 40 — — 300 475 650 300 475 650 300 475 650 Note: 1. Within-device skew is defined as identical transitions on similar paths through a device; n = 0, 1, 2 m = a, b, c, d. M9999-032006 hbwhelp@micrel.com or (408) 955-1690 3 SY10E171 SY100E171 Micrel, Inc. 28-PIN PLCC (J28-1) Rev. 03 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB USA http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2006 Micrel, Incorporated. M9999-032006 hbwhelp@micrel.com or (408) 955-1690 4